Anchor mount

Sib,Frib & Rib modifications.
Share your mods with the forum
chris moody
Supporting Member
Posts: 1456
Joined: 24 Mar 2015, 12:19
Boat Make: Honwave T32IE
Outboard: Tohatsu 9.8
MMSI Number: 235900806
Location: Davetry & Porchester
Has thanked: 42 times
Been thanked: 163 times
Contact:

Re: Anchor mount

Post by chris moody » 13 Jun 2018, 16:06

Best place to tie off the anchor warp to is the end of the painter, then no chance of any rubbing or chafing of tubes
Chris Moody

Tiny Tigga - Honwave T32IE with launch wheels Honda 2hp 4 stroke air cooled & Tohatsu 9.8 2 stroke
Tigga 2 - Ribcraft 4.8 Honda BF50
http://twitter.com/aslmarine

Mitch
Supporting Member
Posts: 250
Joined: 16 May 2017, 16:31
Boat Make: Honwave T38-ie2
Outboard: Mercury 20HP Fourstroke
MMSI Number: 10
Location: Swindon
Has thanked: 66 times
Been thanked: 33 times

Re: Anchor mount

Post by Mitch » 13 Jun 2018, 16:27

Spiffy, this is what i’ll Be using,
The fair lead is glued over the top of the tube for the anchor rope to slide in
DC7DAA04-D1C8-42B3-80E0-8B27C5F31775.jpeg
The railblaza cleat port which is placed below the fair lead is used to tie off the anchor.
8E366CCF-9E9A-4C10-BB32-0F345311BB00.jpeg

Shaun
Newish Member, But I Like It Here
Posts: 34
Joined: 05 Mar 2018, 15:15
Boat Make: F-Rib 430
Outboard: Evinrude E-Tec 30
Location: Epsom
Has thanked: 2 times
Been thanked: 2 times

Re: Anchor mount

Post by Shaun » 14 Jun 2018, 10:37

Do you have links where to buy these please.

Mitch
Supporting Member
Posts: 250
Joined: 16 May 2017, 16:31
Boat Make: Honwave T38-ie2
Outboard: Mercury 20HP Fourstroke
MMSI Number: 10
Location: Swindon
Has thanked: 66 times
Been thanked: 33 times

Re: Anchor mount

Post by Mitch » 14 Jun 2018, 21:11


Shaun
Newish Member, But I Like It Here
Posts: 34
Joined: 05 Mar 2018, 15:15
Boat Make: F-Rib 430
Outboard: Evinrude E-Tec 30
Location: Epsom
Has thanked: 2 times
Been thanked: 2 times

Re: Anchor mount

Post by Shaun » 19 Jun 2018, 10:18


Mitch
Supporting Member
Posts: 250
Joined: 16 May 2017, 16:31
Boat Make: Honwave T38-ie2
Outboard: Mercury 20HP Fourstroke
MMSI Number: 10
Location: Swindon
Has thanked: 66 times
Been thanked: 33 times

Re: Anchor mount

Post by Mitch » 20 Jun 2018, 09:09

Spiffy, have phoned Henshaws up to get the faileader but they want £50 min order so will look somewhere else, if I cant find another then maybe i'll buy a couple to make up the order then i'll have a spare to pass onto someone else.

Shaun
Newish Member, But I Like It Here
Posts: 34
Joined: 05 Mar 2018, 15:15
Boat Make: F-Rib 430
Outboard: Evinrude E-Tec 30
Location: Epsom
Has thanked: 2 times
Been thanked: 2 times

Re: Anchor mount

Post by Shaun » 20 Jun 2018, 09:50

Mitch wrote:
20 Jun 2018, 09:09
Spiffy, have phoned Henshaws up to get the faileader but they want £50 min order so will look somewhere else, if I cant find another then maybe i'll buy a couple to make up the order then i'll have a spare to pass onto someone else.
Thanks, but looking at the front of the f-rib430 adding that would be a problem. They decided to put a wacking big FRIB logo patch on the front. So im going with the Railblaze and designing a bracked to 3d print that will allow the rope to be supported and not tough the tube. Not sure if ill make it static or allow it to swivel yet. Ill think about it once i have the cleatport mounted.

Post Reply

Return to “DIY & Modifications”